Hook up mono amp to 2 subs. How to Wire 2 Subwoofers on a Mono Amplifier

Hook up mono amp to 2 subs Rating: 8,6/10 1265 reviews

Can you hook up 2 subs to a mono amp

hook up mono amp to 2 subs

Why wire in series or parallel? I am having trouble finding the exact same sub so was just wondering as long as the specs are the same, they should work together right? Any help or links would be great! As an alternative, you could wire each sub to a set of output terminals. The disadvantage of bridging is that bridged channels can't drive impedance loads as low as they can when unbridged. I have a pair of 12 inch Cerwin Vega V122Dv2 subs, dual voice coil, 450 watts rms, impedence selector for 4 or 1ohm in a sealed box. I was looking into your Rockford Fosgate R2D2-10 or R2D4-10. I recommend getting separate amps for your different model subs. In this article, we'll help you find the best subwoofer wiring diagram for hooking up your system.


Next

Can i hook up 2 subs to a mono amp

hook up mono amp to 2 subs

Note: preparing to simply install a mono amplifier than one volume control you need both a mono amp. Using the diagram as a guide, on each rear-facing sub you'd switch the wires of the outer terminals - what was once wired to the positive terminal now goes to the negative terminal, and vice versa. If there were three 4 ohm speakers in series, the total impedance will be 12 ohms. I am unsure about two things: 1:should i purchase the two or four ohm voice coil subs? So on is +- an other is -+ an the wires hooked up verly reach cause they were cut short. Just pretend, in the upper diagram, that the two amps share the same chassis and do not need the extra power, ground, or turn-on lead wires.

Next

How Do You Hook Up A Mono Amp To Two 12 Subs

hook up mono amp to 2 subs

So would the best way to go about it just to be to hook up a single voicecoil to each terminal for a 2ohm load? I worked in my high school's stage crew, running sound, lights, and a movie projector. . Which one will work better with my set up? Driverguru - 1600w class d digital signal wire for reference only one positive. I know I would be using half of the 124, but with a combined rms rating of 800 watts minus the 200 lost for the unused coil. That amplifier isn't stable for a 1-ohm load, so that's probably what you're hearing: the amp freaking out. Working in a music store in Austin, Texas, I spent a few years manufacturing, installing, repairing, and operating sound systems.

Next

Mono amp with outputs for 2 subs

hook up mono amp to 2 subs

A good way to prevent speakers from playing low notes is with. I'm deciding whether or not to buy the identical amp and run the other sub off it. Contact us by phone, chat, or email and an Advisor will help you get what you need. Is this the best and only safe way to run this with a factory amplifier? And what would be the best way to wire them? Liandi has traveled extensively in Europe and East Asia and incorporates her experiences into her articles. Like everyone else, I want all I can get out of the amp, but I don't want to burn it up.

Next

Hooking up a mono amp with two subs?

hook up mono amp to 2 subs

Is there a way to get a 4 ohm load? Are the subs' power-handling ratings high enough to survive that amp's output? So a hi low converter would have to be installed. You could also wire each sub's voice coils in series and then wire the subs together in series again to get an 8 ohm load. Connect the positive lead of the speaker wire to the positive terminal, and the negative to the negative. This is the right way to hook 2 4 ohm subwoofers up 2 ohms. I just like using 2 individual runs. How does the amp perform with different impedance loads? The only safe way to wire that sub is. How do I wire this sub to this amp? Both negatives are connected to the same contacts in side as well as the positives.

Next

Hooking up 2 subs to one alpine d mono amp

hook up mono amp to 2 subs

Would running them separately cut the ohms in half or would each speaker stay at 4ohms? That would be 1200W, and what wiring scheme would you recommend for this? Subwoofer voice coils usually come in 2-ohm, 4-ohm, or 8-ohm impedances. To help you through the process, check out our article. That's 200 watts less power, but you gain some space by removing an amp. Bridged mode Bridging an amp combines two amplifier channels into one, to get more power. And if so, is this parallel or series.

Next

How to Wire 2 Subwoofers on a Mono Amplifier

hook up mono amp to 2 subs

Note: wire from your amp is possible with a mono amp, it has two subwoofers to a b. Also the more air you move the better the response on lower bass notes. I want to double it up and add another sub with it. For your installation, you would want to reverse the polarity of the two rear-facing subs. Also, can these speakers be wires to 1 ohm? This seems like the safest way, the subs will get the recommended power? Or does that present a 2ohm load? But I would really like to run them off that mono amp. When using a multimeter to set gain is the correct formula for this situation square root of 1600 x 2. Amplifier output An amplifier will put out more power through a low-impedance sub than it will through a high-impedance sub.

Next

Mono amp with outputs for 2 subs

hook up mono amp to 2 subs

Check this out for help with your wiring. Wire the sub itself in parallel and get a 2ohm output? But a lower impedance also means more stress on the amp. From everything I've read on this site, this should work just fine, if not well, correct? Is mixed impedance a concern under the following configuration? For your set-up, that's exactly what you can do: wire one sub to each set of terminals. Can I run a postive wire from my 6. Now I've done some research and the amp is stable at 2ohm in stereo, not bridged. If you bought your amp from Crutchfield, you could call Tech Support for free help troubleshooting your system. Two ohms, then you wish to add a mono, you subwoofers.

Next